JDennis
Member
After reading the different posts, I would like to get an M10 Die with Plug tap, and an M12 Die with Plug Tap.
Two questions: are the dies round or hex?
Also, are these made for Ferrous metals?
I'll are jump in if there is still room.
M10 set please with a bottom tap
M10 taper tap also please.
This way I'll have both taps. I looked at my other taps that I got on group buys here and like Justin has said they are tapered. Those were all triple start so not sure if that matters or not.
OK, I'll put my name down for a M10 set ( plug tap )
and a M12 set ( plug tap )
If I understand it correctly, the plug tap has a small taper, we used to call this an intermediate tap.
Is there still room for some of us that jumped on board yesterday?
If there is room for more in this buy I would be interested in:
M10 bottoming tap
M10 second tap
M10 die
M12 bottoming tap
M12 second tap
M12 die
Two questions: are the dies round or hex?
Also, are these made for Ferrous metals?
Is there still room for some of us that jumped on board yesterday?
If there is room for more in this buy I would be interested in:
M10 bottoming tap
M10 second tap
M10 die
M12 bottoming tap
M12 second tap
M12 die
Mark, I had you marked down for just that.
I am interested in Buying a set of Both the 10m, and the 12m.
Thanks
They are round adjustable and the material is HSS 60-62 Rockwell. I know the HSS but not the numbers and rockwell. I can look it up but HSS is enough for me.
I am interested in Buying a set of Both the 10m, and the 12m.
Thanks
Just so I can plan appropriately....
Is there a planned close date for this group buy? Or did I miss it?
They are round adjustable and the material is HSS 60-62 Rockwell. I know the HSS but not the numbers and rockwell. I can look it up but HSS is enough for me.
I think the question I was trying to ask was "what type of metal can these be used on, i.e., stainless, aluminum, brass, copper, titanium, etc., if any". I'm only wondering since my primary use will be for stainless, and titanium. Maybe the steel that these are made from is only good for the softer metals.
I also didn't know you were waiting on me. What do I have to do to confirm? The spreadsheet shows me for both sets, but I just want the 10MM set. Also, I think I want a plug tap, not the taper tap.
I would like to go for the M12 double full set (tap &die).
Thanks.
Twinturbine stays with double set of 10 and 12 taper tap. I really believe I will need taper for hard burls/stabilized and metals. Most tapers are not too long for me, just cannot use last 1/8 end plus the taper acts as a slow brake/ hold. I'm not much long on pens but have had a metal lathe all my life, only had a shotgun before.
I would like to go for the M12 double full set (tap &die).
Thanks.
If not to late, can you change my order to just a "Plug" tap and die for each the M10 & M12 sets, cancelling the bottom taps.
I'd like in on this please.
M10 set(plug tap-die)
M12 set(plug tap-die)
I would like to go for the M12 double full set (tap &die).
Thanks.
M 10
Double taper
Double bottoming
Double die
M12
Double taper
Double bottoming
Double die
For everyone requiring information on taps and die, check this link out below.
Sure it will make it clear for everyone.
File:TapTypes.gif - Wikipedia, the free encyclopedia
M 10
Double taper
Double bottoming
Double die
M12
Double taper
Double bottoming
Double die
For everyone requiring information on taps and die, check this link out below.
Sure it will make it clear for everyone.
File:TapTypes.gif - Wikipedia, the free encyclopedia
Just noticed you have me down for the plug taps on the spread sheet Ty.
If not to late I would like the following in double start M10: Tap and a bottoming tap M10: Die Donovam